how to reset mass air flow sensor bmw

Position the MAF sensor on the throttle body. Cleaning dirty MAF sensor in BMW X3.

Us 859 X 100 Pad2 Special Functions Expert With Vw 4th 5th Immo Key Programmer Programmer Obd

Install the new MAF on your BMW.

. Install a new mass air flow sensor into the air filter housing. CRC MAF Mass Air Flow Sensor Cleaner. The stored compensation factors are reset to 0 in the process.

To Check if Air-Mass has been reset Select Air-Mass Flow Sensor Adjustment again and Stored information should be 00 as above To exit Select NO Error Resetting Air-Mass Fig14 If Error occurs as above please report this number to Launch so we can add this new system. Just double checked on my BMW system hex code would be 3ff0 air-mass flow sensor. Disconnect mass air flow sensor harness connector.

Httpsamznto2KqcW0BIn BMW terminology - Hot Film Air Mass Meter - which is also known as a MAF or mass air flow s. Remove the sensor from the housing. Code 3263 oxygen sensor.

Unplug the electrical connector. Tighten the mounting screws to 27 in lb 3 Nm. How to Reset the Mass Air Flow Sensor.

The mass air flow sensor is part of the engines intake system and is. Remove the MAF sensor mounting screws. Next disconnect air flow meter electrical connector by pressing wire clip purple arrow and pulling it straight off.

The transformation was remarkable - the engine seemed to pull with. Locate the mass airflow sensor by the engine air filter housing on the drivers side. Restart engine and let it idle for at least 5 seconds.

When you change a MAF sensor you need to disconnect the battery for about 10 minutes so the computer forgets the learned parameters and resets to the factory parameters. Remove the two T20 Torx fasteners from the mass air flow sensor green arrows. How to change Mass Air Flow Sensor on your BMW car yourself.

Disconnect mass air flow sensor harness connector. Remove the sensor from the intake air duct. I bought a 2004 X3 recently and even though the Check Engine light was not on I did buy a can of Mass Air Flow sensor cleaner and cleaned the MAF.

Connect the mass air flow MAF sensor electrical connector. The following learned values will return to the initial state. Restart engine and let it idle for at least 5 seconds.

Turn ignition switch OFF. Perform this coding also after removing the leak on the intake system. The hood release is located under the dashboard on the drivers side.

But if you let the car idle instead then the mass air flow sensor should reset. Intake manifold flap actuator. Then unclip the two spring clips green arrows that hold the mass air flow sensor.

If stuck use a small flathead screwdriver to gently lever it out of the duct. Use q-tip or MAF cleaner soaked paper towel to gently clean exposed wire sensor. Only show this user.

Remove the Torx screws that hold the mass airflow sensor in place. Returning learned values of the intake system to the initial state. How do you reset a mass air flow sensor.

We sell oem air mass sensors air flow meters and hfms hot film meter. Intercooling of charge air. Make Model Car parts category Find.

HOW TO CLEAN MAF SENSOR MASS AIR FLOW SENSOR ON BMW E46 E39 E53 E83 X3 X5 Z3 Z4 E60 E65If you have BMW and you have code P0102 or code P0113 this is the righ. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air. Install the MAF sensor mounting screws.

The engine still drove like it was a bit breathless so I bit the bullet and bought a brand new MAF sensor. Find the location of the MAF sensor in your X3 it will be somewhere between the air filter box and the throttle body. BMW Diagnostics with ISTA - How to reset mass air flow MAF adaptation values with ISTA DThe information contained on this video are for educational and info.

Start engine and warm it up to normal operating temperature. Remove the MAF sensor from the throttle body. Then it goes into learn mode and may take a little while before it learns all the parameters of the new MAF sensor.

Figure 9 Working in the engine compartment loosen air flow meter clamp green arrow then disconnect the air duct from air flow meter by pulling straight off air flow meter. Disconnect mass air flow sensor harness connector. Ratio of calculated to measured air mass too high.

Stop engine and reconnect mass air flow sensor harness connector. The most common signs of bad mass air flow sensor MAF in BMW 1 Series are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe. Disconnect the mass air flow MAF sensor electrical connector.

Changing BMW Mass Air Flow Sensor yourself manuals and video tutorials. Erase the DTC memory. Intake manifold flap actuator.

Turn ignition switch OFF. Unplug the electrical connector from your BMW mass airflow sensor. The PCM detects that the actual MAF sensor frequency signal is not within a predetermined range of the calculated MAF value for more than 40 seconds.

How to clean the mass air flow sensor on your BMW e46. Start engine and warm it up to normal operating temperature. Stop engine and reconnect mass air flow sensor harness connector.

Helpful guides and tips on replacing BMW Mass Air Flow Sensor. When the battery is removed all MAF sensors will be reset in about 10 to 15minutes time.

P0100 Mass Air Flow Circuit Malfunction